• Include mitigation procedures for:
  • Beam hazards
  • Non-beam hazards
  • Biological hazards
• Consider conditions necessary for safe laser operation when devising hazard control measures:
  • Anticipate potential eye exposure during alignment
  • Ensure optics are aligned
  • Use appropriate eye protection
  • Ensure safe methods of handling high voltage
  • Prevent unprotected personnel from entering the laser area
  • Ensure new operators are trained in safety procedures
  • Anticipate and provide protection for ancillary hazards
  • Double-check proper restoration of equipment following service

  Back to top

• Use the minimum laser radiation level required for the application. If a laser or laser system emits excessive radiation, the EH&S Laser Safety Officer (LSO) may order a reduction of power to a level commensurate with the required application.
• Maintain the laser beam at a height other than the normal sitting or standing position of a person.
• Use protective housing on all lasers and laser systems. (Note: In certain instances, operation of a laser or laser system without a protective housing may be necessary. In these cases, contact the Laser Safety Officer, (858) 822-2850, to arrange alternative control methods.)
• Perform alignment of laser optical systems so that the primary beam, specular, or diffuse reflection does not expose the eye above the applicable maximum permissible exposure (MPE) limit.
  • See ANSI Z136.5–2000 Tables A1 and A2, Maximum Permissible Exposure for the Eye (PDF) (Word file).
• Evaluate non-beam hazards and incorporate mitigation procedures into your Laser Safety Plan.

  Back to top

• Interlocks on protective housing are required for class 3b and 4 lasers. Interlocked protective housing is activated upon removal of the protective housing during operation and maintenance. The interlock is designed to prevent access to the beam above the applicable maximum permissible exposure (MPE) limit.
  • See ANSI Z136.5–2000 Tables A1 and A2, Maximum Permissible Exposure for the Eye (PDF) (Word file).
  • Remote interlock connectors are required for class 4 lasers and strongly recommended for class 3b lasers. Interlocks facilitate electrical connections to an emergency master switch. When the terminals of the connector are open circuited, the accessible radiation must not exceed the appropriate MPE levels.
  • Key control is required for class 4 lasers. Restrict the key or code that enables operation of a class 4 laser or laser system to an appropriate supervisor or authorized laser operator. Disable the master switch when the laser is not in use.
  • Viewing portals and diffuse display screens, which are part of a laser or laser system, must incorporate a suitable means (such as interlocks, filters, or attenuators) to maintain the laser radiation at the viewing position at or below the applicable MPE.
  • Collecting optics (lenses, telescopes, microscopes, etc.) intended for viewing use with a laser or laser system must incorporate suitable means (such as interlocks, filters, or attenuators) to maintain the transmitted laser radiation at levels at or below the appropriate MPE.
  • A completely exposed or partially exposed beam path from a class 3b or 4 laser or laser system requires the EH&S Laser Safety Officer to conduct a hazard analysis to establish the Nominal Hazard Zone (NHZ) if not furnished by the manufacturer.
  • A beam stop or attenuator is required for class 4 lasers and is strongly recommended for class 3 lasers. The beam stop or attenuator must be capable of preventing laser radiation in excess of the appropriate MPE level.
  • Built in activation warning systems for class 4 lasers and laser systems may include audible sound (bells or chimes), warning lights, or verbal countdown. An audible warning system notifies personnel that the laser is either about to be activated or deactivated.

  Practice special control measures for invisible laser radiation if infrared or ultraviolet radiation is involved.

  Back to top

• Use a visible coaxial aiming beam, if possible, or a phosphorus card for alignment.
• For infrared lasers (IR):
  • Terminate the beam from class 3b IR lasers with a highly absorbent backstop.
  • Terminate the beam from class 4 IR lasers with a fire-resistant material.
  • Note: Select materials carefully. Many surfaces which visually appear "dull" can act as a reflector of infrared radiation.
• For ultraviolet (UV) lasers:
  • Use appropriate shielding materials to attenuate the radiation level below MPE for the specific UV wavelength.
  • Be alert to the possibility of producing hazardous byproducts, such as ozone, and the formation of skin sensitizing agents.
  • Caution: Toxic gases, such as F², Cl², NF³, etc., may be produced with the use of UV lasers, and should be guarded against when invisible radiation is accessible from a class 3 or class 4 laser system.
  • Display warning signs and/or lights in a conspicuous location to alert personnel in the area when then the laser is activated.

  Back to top

• Take these special precautions in addition to the laser control measures required by hazard classification:
  • If disconnection occurs and the resulting laser radiation is below the applicable MPE by engineering controls, connection or disconnection can be done in an uncontrolled area.
  • Connection or disconnection must be done in an appropriate controlled area during operation if the laser radiation is greater than the applicable MPE.

  Back to top

Laser hazard signs and labels must meet American National Standard (ANZI) Z535, Specifications for Accident Prevention Signs, ANSI Z534 series, latest revision. Signs and labels prepared in accordance with previous standards are acceptable. Environment, Health & Safety (EH&S) provides signs and labels to UCSD researchers upon request.

Follow the label and signage requirements below:

• Laser hazard signs:
  

  Laser hazard sign	Laser alignment or repair sign

  • Post all entrances to laser control areas with laser hazard signs.
  • Use the signal word "Danger" on all signs and labels associated with class 3a lasers or laser systems that exceed the appropriate MPE for irradiance, and all class 3b and 4 lasers and laser systems. (See red image above.)
  • Use the signal word "Notice" on all signs posted outside temporary laser control areas, such as during alignment, service, or repair. (See blue image above.)
  • Print or legibly write specific information at the following 3 positions on a laser hazard sign:
  • Position 1, above the tail of the sunburst – Describe special precautionary instructions or protective actions. This may include the following elements:
  • Required protective eyewear
  • Invisible laser radiation
  • Knock before entering
  • Do not enter when light is on
  • Restricted area
  • Position 2, below the sunburst tail – Indicate the following information, as applicable:
  • Type of laser (i.e., YAG, Helium-Neon, etc.)
  • The emitted wavelength
  • Pulse duration (if appropriate)
  • Maximum output
  • Position 3, lower left corner – Indicate the class of the laser or laser system.
• Request signs and labels as needed from the EH&S Laser Safety Officer, (858) 822-2850.

  Back to top

• Allow maintenance and repair work on laser systems to be performed only by certified service personnel who have documented training for the laser system to be serviced.
• Ensure repair and service personnel take appropriate safety precautions to protect themselves, lab personnel, and the general public within the vicinity.
• Post a sign with the signal word "Notice," (see image below) in a conspicuous location outside the laser control area to indicate repairs or alignment procedures are underway.
  • State pertinent safety information on the sign. Read about warning signs above for details.
  • Post the sign for the duration of service or repair.
  
  

  Laser alignment or repair sign

  Back to top

• Read Requirements for Class 3b and 4 Lasers for specific SOP requirements.
• Keep the SOP easily accessible for operators and service personnel.

  Back to top

• Determine the status of your facility by doing the following:
  • Contact the EH&S Laser Safety Officer, (858) 822-2850, to conduct an analysis of your facility. If the analysis determines that a class 3b or 4 laser will be used, a laser control area will be established.
• For class 3b indoor control areas: These measures are required for class 3b lasers, and advisory for class 3a lasers.
  • Restrict access. Keep doors locked to prevent unauthorized access to the control area.
  • Post laser hazard warning signs on entrances to the controlled area.
  • Permit only authorized, trained personnel to operate the laser equipment.
  • Admit untrained personnel or spectators only if authorized by the laser operator, under supervision, and after they have been informed about safety requirements and provided with protective eyewear (if required).
  • Place special emphasis on control of the beam path if the laser beam is not enclosed.
• For class 4 indoor laser control areas: High-power lasers require extra control measures due to greater risk of injury from the direct or specular reflected beam, and hazardous diffuse reflections.

  Implement the class 4 precautions below in addition to the measures described above:

  • Locate class 4 lasers in an area designed solely for laser operation.
  • Control the entire beam path capable of producing hazardous reflections.
  • Install safety locks or interlocks to deactivate the laser in the event of an unexpected entry into the laser control area.
  • Design the interlock to allow both rapid egress by the laser personnel and admittance under emergency conditions.
  • Enable the individual in charge of the control area to momentarily override the room access interlocks.
  • Design an override feature that prevents automatic re-energizing of the power supply and requires the manually re-setting power to the shutter.
  • Install a control-disconnect switch, or "panic button," for deactivating the laser.

  Back to top

• Obtain permission to operate lasers or laser systems outdoors on UCSD property from the LSO prior to initial use.
  • Submit a written request to the EH&S Laser Safety Officer at Mail Code 0089.
• Design the laser control area to prevent any scatter or reflected laser radiation from exiting the area.
• Configure the beam path so it's inaccessible to audiences or pedestrians.
• Secure power sources and wires to prevent tripping or other inadvertent accidents.

  Back to top